ola5doc/content/.stversions/quentin/sources/text~20171217-144831.txt

How to Use a Drill Safely


are one of
the most convenient tools for DIY projects, but like all power tools, they need to be handled safely. Knowing how to
correctly will help
you prevent injury from flying shards of broken material or improperly handled electricity. If you ever have a safety question that this guide does not answer, your drill's manual is a good place to look next.

Preparing to Drill

1
Wear safe clothing and eye protection. Avoid baggy clothing or dangling jewelry that could catch in the
as you lean
over it. Wear safety goggles or glasses that cover the sides of your eyes, to protect them from flying debris.

2
Wear ear protection if drilling regularly. A handheld electric
produces about 90
decibels, which is just enough to cause hearing damage after prolonged exposure. Most cordless
are quiet enough
that hearing protection is not necessary.

Impact drills (hammer drills) are the loudest handheld drills, producing over 100 dB. Hearing protection is recommended whenever using them.

3
Protect your lungs when necessary. If the project kicks up a lot of dust, wear breathing protection. A dust mask is only good for short-term comfort. Use a respirator if you
regularly or for
long periods of time, or if the material you are
is a known
respiratory hazard.

Each respirator is rated for certain types of hazards. Make sure the one you use is suited to your project.


4
Choose the correct drill bit. Using a bit made from the wrong material can cause the bit or the material you're drilling to break. You can use a general-purpose bit on most wood; a masonry bit for stone, brick or concrete; an HSS (high speed steel) bit on most metals; and a carbide or diamond-tipped bit on very hard, brittle surfaces such as porcelain, glass, or glazed tiles.[3] There are many specialized bit designs, so consult the
manual or bit
manufacturer if you're not sure which bit to use.

When
a hole for
a screw, there's an easy way to find the right size bit. Hold the screw up directly behind the bit. The bit should hide the shaft of the screw from view, but the screw threads should still be visible on both sides.

5
Fit the
bit firmly into
the chuck. The chuck is the clamp in the "jaws" of the
This holds the

bit in place
as it spins. To replace a drill bit, make sure the drill is off (and unplugged if corded), then loosen the chuck by rotating it. Depending on the drill, you may be able to do this by hand, or you may need a chuck key located in a compartment in the top or handle of the drill.[5] Insert the
bit into the
chuck, then tighten again. Make sure the bit is straight and secure, and remove the key before you turn on the drill.

Each chuck has a maximum size. Most
made for home
use in the United States have a chuck of size 1/4", 3/8", or 1/2". The shaft of the
bit must be
smaller than this size (but the tip can be larger).[6]
Run the
and watch the
bit spin in the air. If it wobbles from side to side (or looks like a blurry cone), the bit is bent or not secured correctly. Discard bent bits, since they can easily break during drilling

6
Clamp small pieces together. If you are drilling into a small, loose piece, clamp it down firmly before you
Do not hold
the piece down with one hand while drilling, as the
could slip and
injure you.[8] `

7
Handle the cord safely. If the drill has a cord, never leave it stretched across a pathway when not in use. Never pick up the drill by the cord. If you are
in a wet
or muddy area, use a cordless drill instead.[9]

If you need to plug the
into an extension
cord, check the
manual for the
minimum wire gauge (or go with 16 gauge if you're not sure).[10] Do not chain multiple extension cords together, use indoor extension cords outdoors, or use an adapter to plug a three-prong cord into a two-prong outlet.[11]

Drilling Safely

1
Drill a pilot hole. In many cases, you'll get better results if you start with a
bit a little
smaller than the final hole size. Drill a shallow "pilot hole," then switch to the larger bit to finish the job. The pilot hole will help prevent your drill bit from slipping, and reduces the chance of splitting wood or other damage.[12]

Very brittle materials such as ceramic and glass require extra care. Make a small "X" in masking tape where you want the hole, to help prevent slipping and chipping. Instead of drilling the pilot hole, place the
bit over the
X, then gently tap it with a hammer to create a small dent.

2
Drill with steady pressure. Hold the
steady and push
it into the material you're
If it takes
more than light force to drill the hole, you're probably using the wrong bit.[13]

3
Adjust the clutch. Each
has a twistable
collar to adjust the torque, often with a series of numbers on it. The higher the number, the more torque (rotational force) the drill will apply. If you are having trouble penetrating the material, increase the torque. If you are over-driving screws (burying them too deep), or if
too deep could
damage something, lower the torque.

Some models mark the highest torque with a drill bit icon.[14]

4
Avoid overheating the drill bit. If you are
through hard materials
or drilling at high speeds, the
bit will encounter
an immense amount of friction. This can rapidly overheat the bit, to the point where it becomes red hot or burns the material you're
Start at low
drill speeds, and only increase the speed if the drill isn't moving smoothly. If you're drilling through hard materials, or
many holes in
any material, stick to slow speeds and pause occasionally to give the bit a few seconds to cool down.

When drilling glass, ceramic, or stone, give the bit a steady supply of water to keep it cool. One way to do this is to build a "dam" out of putty or modeling clay around your drilling area. Fill the area with water so it flows down into the hole. "Pump" the bit up and down so the water can reach the tip.[15]
Even if the drill bit doesn't look hot, give it time to cool down before touching it.

5
Do not force a jammed bit through. If the
bit gets stuck
in the material, don't try to force it out by running the drill. Unplug the drill, separate the bit and the chuck, and remove the bit using manual tools.[16]