Compare commits
No commits in common. "3d525d6a3a54afe90ca337e40bd5610369206085" and "c5b402a1b4f463ed2dc1fa6ecbdeded455cea37e" have entirely different histories.
3d525d6a3a
...
c5b402a1b4
|
|
@ -0,0 +1,121 @@
|
|||
#define MY_DEBUG
|
||||
// Enable and select radio type attached
|
||||
#define MY_RADIO_RF24
|
||||
// #define MY_RF24_PA_LEVEL RF24_PA_MIN
|
||||
// #define MY_RF24_PA_LEVEL RF24_PA_LOW
|
||||
#define MY_RF24_PA_LEVEL RF24_PA_HIGH
|
||||
//#define MY_RF24_PA_LEVEL RF24_PA_MAX
|
||||
|
||||
#define MY_RF24_CHANNEL 14
|
||||
|
||||
#define MY_REPEATER_FEATURE
|
||||
|
||||
#include <SPI.h>
|
||||
#include <MySensors.h>
|
||||
|
||||
#define ROTATION_CHILD_ID 0
|
||||
|
||||
MyMessage dimmerMsg(ROTATION_CHILD_ID, V_DIMMER);
|
||||
MyMessage lightMsg(ROTATION_CHILD_ID, V_LIGHT); // we need init light message to make the dimmer appear in HA
|
||||
|
||||
/*
|
||||
control a 28BYJ-48 stepper motor with ULN2003 driver board
|
||||
https://www.makerguides.com/28byj-48-stepper-motor-arduino-tutorial/
|
||||
*/
|
||||
|
||||
#include "Stepper.h"
|
||||
|
||||
// Define number of steps per rotation:
|
||||
const int stepsPerRevolution = 2048; // can be 4096
|
||||
|
||||
// ULN2003 Wiring:
|
||||
// Pin 3 to IN1
|
||||
// Pin 4 to IN2
|
||||
// Pin 5 to IN3
|
||||
// Pin 6 to IN4
|
||||
|
||||
// Create stepper object called 'myStepper', note the pin order:
|
||||
Stepper myStepper = Stepper(stepsPerRevolution, 3, 5, 4, 6);
|
||||
|
||||
int prevDimValue=0;
|
||||
int newDimValue=0;
|
||||
char convBuffer[10];
|
||||
|
||||
void presentation()
|
||||
{
|
||||
#ifdef MY_DEBUG
|
||||
Serial.println("- - - - - presentation - - - - -");
|
||||
#endif
|
||||
|
||||
sendSketchInfo("Registre Air Chaud", "0.1");
|
||||
|
||||
present(ROTATION_CHILD_ID, S_DIMMER, "rotation");
|
||||
}
|
||||
|
||||
void setup() {
|
||||
#ifdef MY_DEBUG
|
||||
Serial.println("- - - - - setup - - - - -");
|
||||
#endif
|
||||
|
||||
myStepper.setSpeed(5); // Set the speed to 5 rpm:
|
||||
|
||||
// todo make a homing of stepper motor OR find a way to sensorize where it is
|
||||
|
||||
send(dimmerMsg.set(prevDimValue));
|
||||
send(lightMsg.set(1));
|
||||
}
|
||||
|
||||
void loop() {
|
||||
#ifdef MY_DEBUG
|
||||
// Serial.println("- - - - - loop - - - - -");
|
||||
#endif
|
||||
delay(5000);
|
||||
}
|
||||
|
||||
// Handle incoming messages
|
||||
void receive(const MyMessage &message) {
|
||||
|
||||
#ifdef MY_DEBUG
|
||||
Serial.println("- - - - - receive - - - - -");
|
||||
Serial.print("Last reading for sensor: ");
|
||||
#endif
|
||||
|
||||
if (message.type == V_LIGHT) {
|
||||
|
||||
#ifdef MY_DEBUG
|
||||
Serial.println("- - - - - receive V_LIGHT - - - - -");
|
||||
#endif
|
||||
|
||||
} else if (message.type == V_DIMMER) {
|
||||
|
||||
#ifdef MY_DEBUG
|
||||
Serial.println("- - - - - receive V_DIMMER - - - - -");
|
||||
#endif
|
||||
|
||||
newDimValue = atoi(message.getString(convBuffer));
|
||||
|
||||
#ifdef MY_DEBUG
|
||||
Serial.print("prevDimValue: ");
|
||||
Serial.println(prevDimValue);
|
||||
Serial.print("newDimValue: ");
|
||||
Serial.println(newDimValue);
|
||||
#endif
|
||||
|
||||
int quart = stepsPerRevolution / 4; // how many rotation do we want max (here 45° so from 0 to 512 steps)
|
||||
int diff = prevDimValue - newDimValue; // get the difference between the previous and the new dimm value
|
||||
prevDimValue = newDimValue; // record new dimm as previous dimm
|
||||
int steps = (quart / 100) * diff; // convert diff on percent to steps
|
||||
#ifdef MY_DEBUG
|
||||
Serial.print("quart: ");
|
||||
Serial.println(quart);
|
||||
Serial.print("diff: ");
|
||||
Serial.println(diff);
|
||||
Serial.print("steps: ");
|
||||
Serial.println(steps);
|
||||
#endif
|
||||
|
||||
myStepper.step(steps); // move the stepper
|
||||
|
||||
// todo release the stepper motor to free power consumption
|
||||
}
|
||||
}
|
||||
|
|
@ -1,165 +0,0 @@
|
|||
#define MY_DEBUG
|
||||
// Enable and select radio type attached
|
||||
#define MY_RADIO_RF24
|
||||
// #define MY_RF24_PA_LEVEL RF24_PA_MIN
|
||||
// #define MY_RF24_PA_LEVEL RF24_PA_LOW
|
||||
// #define MY_RF24_PA_LEVEL RF24_PA_HIGH
|
||||
#define MY_RF24_PA_LEVEL RF24_PA_MAX
|
||||
|
||||
#define MY_RF24_CHANNEL 14
|
||||
|
||||
#define MY_REPEATER_FEATURE
|
||||
|
||||
#define MY_DEFAULT_RX_LED_PIN A0
|
||||
#define MY_DEFAULT_TX_LED_PIN A1
|
||||
#define MY_DEFAULT_ERR_LED_PIN A2
|
||||
|
||||
#include <SPI.h>
|
||||
#include <MySensors.h>
|
||||
|
||||
// https://lastminuteengineers.com/multiple-ds18b20-arduino-tutorial/
|
||||
#include <OneWire.h>
|
||||
#include <DallasTemperature.h>
|
||||
|
||||
// Data wire is plugged into port 11 on the Arduino
|
||||
#define ONE_WIRE_BUS 7
|
||||
// Setup a oneWire instance to communicate with any OneWire devices
|
||||
OneWire oneWire(ONE_WIRE_BUS);
|
||||
|
||||
// Pass our oneWire reference to Dallas Temperature.
|
||||
DallasTemperature sensors(&oneWire);
|
||||
|
||||
#define ROTATION_CHILD_ID 0
|
||||
#define CHILD_ID_TEMP 1
|
||||
|
||||
MyMessage dimmerMsg(ROTATION_CHILD_ID, V_DIMMER);
|
||||
MyMessage lightMsg(ROTATION_CHILD_ID, V_LIGHT); // we need init light message to make the dimmer appear in HA
|
||||
MyMessage msgTemp(CHILD_ID_TEMP, V_TEMP);
|
||||
|
||||
// https://lastminuteengineers.com/28byj48-stepper-motor-arduino-tutorial/
|
||||
#include "AccelStepper.h"
|
||||
|
||||
|
||||
// ULN2003 Wiring:
|
||||
const int In1 = 3;
|
||||
const int In2 = 4;
|
||||
const int In3 = 5;
|
||||
const int In4 = 6;
|
||||
|
||||
// Create stepper object called 'myStepper', note the pin order:
|
||||
AccelStepper myStepper(4, In1, In3, In2, In4);
|
||||
|
||||
int prevDimValue=0;
|
||||
int newDimValue=0;
|
||||
char convBuffer[10];
|
||||
|
||||
int pos=0;
|
||||
|
||||
unsigned long previousMillis = 0;
|
||||
const long tempInterval = 60000;
|
||||
float DTemp;
|
||||
float old_DTemp;
|
||||
|
||||
|
||||
void presentation()
|
||||
{
|
||||
#ifdef MY_DEBUG
|
||||
Serial.println("- - - - - presentation - - - - -");
|
||||
#endif
|
||||
|
||||
sendSketchInfo("Registre Air Chaud", "0.3");
|
||||
|
||||
present(ROTATION_CHILD_ID, S_DIMMER, "rotation");
|
||||
present(CHILD_ID_TEMP, S_TEMP, "Temperature");
|
||||
}
|
||||
|
||||
void setup() {
|
||||
#ifdef MY_DEBUG
|
||||
Serial.println("- - - - - setup - - - - -");
|
||||
#endif
|
||||
|
||||
myStepper.setMaxSpeed(1000.0);
|
||||
myStepper.setAcceleration(50.0);
|
||||
myStepper.setSpeed(200);
|
||||
// myStepper.moveTo(2038);
|
||||
// todo make a homing of stepper motor OR find a way to sensorize where it is
|
||||
myStepper.setCurrentPosition(0);
|
||||
|
||||
send(dimmerMsg.set(prevDimValue));
|
||||
send(lightMsg.set(1));
|
||||
|
||||
sensors.begin();
|
||||
}
|
||||
|
||||
void loop() {
|
||||
#ifdef MY_DEBUG
|
||||
// Serial.println("- - - - - loop - - - - -");
|
||||
#endif
|
||||
|
||||
unsigned long currentMillis = millis();
|
||||
// do measurement every one minute
|
||||
if (currentMillis - previousMillis >= tempInterval)
|
||||
{
|
||||
previousMillis = currentMillis;
|
||||
sensors.requestTemperatures();
|
||||
old_DTemp = DTemp;
|
||||
DTemp = sensors.getTempCByIndex(0);
|
||||
if (DTemp != old_DTemp && DTemp != -127)
|
||||
{
|
||||
send(msgTemp.set(DTemp, 1));
|
||||
old_DTemp = DTemp;
|
||||
}
|
||||
}
|
||||
|
||||
// myStepper.moveTo(myStepper.currentPosition() + 2048);
|
||||
|
||||
// delay(5000);
|
||||
|
||||
// Change direction once the motor reaches target position
|
||||
// if (myStepper.distanceToGo() == 0)
|
||||
// myStepper.moveTo(-myStepper.currentPosition());
|
||||
|
||||
// Move the motor one step
|
||||
if(!myStepper.run()){
|
||||
// release the stepper motor to free power consumption
|
||||
digitalWrite(In1, 0);
|
||||
digitalWrite(In2, 0);
|
||||
digitalWrite(In3, 0);
|
||||
digitalWrite(In4, 0);
|
||||
}
|
||||
}
|
||||
|
||||
// Handle incoming messages
|
||||
void receive(const MyMessage &message) {
|
||||
|
||||
#ifdef MY_DEBUG
|
||||
Serial.println("- - - - - receive - - - - -");
|
||||
Serial.print("Last reading for sensor: ");
|
||||
#endif
|
||||
|
||||
if (message.type == V_LIGHT) {
|
||||
|
||||
#ifdef MY_DEBUG
|
||||
Serial.println("- - - - - receive V_LIGHT - - - - -");
|
||||
#endif
|
||||
|
||||
} else if (message.type == V_DIMMER) {
|
||||
|
||||
#ifdef MY_DEBUG
|
||||
Serial.println("- - - - - receive V_DIMMER - - - - -");
|
||||
#endif
|
||||
|
||||
newDimValue = atoi(message.getString(convBuffer));
|
||||
|
||||
#ifdef MY_DEBUG
|
||||
Serial.print("prevDimValue: ");
|
||||
Serial.println(prevDimValue);
|
||||
Serial.print("newDimValue: ");
|
||||
Serial.println(newDimValue);
|
||||
#endif
|
||||
|
||||
// todo instead of 1 revolution (2038) define how much revolution we want to do for full opening (100% of the dimmer in HA)
|
||||
pos = (2038 / 100) * newDimValue;
|
||||
myStepper.moveTo(pos); // move the stepper
|
||||
}
|
||||
}
|
||||
Loading…
Reference in New Issue